As an Amazon Associate I earn from qualifying purchases.
1. MakerDoIt #ad
Makerdoit 4pcs Micro Servo Motor SG90, for Robot Arm/Hand/Walking/Servo Door Lock #adMakerDoIt #ad
- Operating voltage: 4. 8v~6v. This servo can rotate approximately 180 degrees 90 in each direction and works just like the standard kinds but smaller. Dead bandwidth: 7usec.
Stall Torque 4. 8v: 17. 5oz /in 1kg/cm. Hardware connectionsthe sg90 has 3 wire interfaces in which the connections should be made as follows: Red wire-5V, Brown Wire-Ground, Yellow wire-digital pin 9. Small sizeit is tiny and lightweight with high output power.
Rotary angle: 180°. Specificationsno load running speed: 012 second/60 at 4. 8v. Package includethe package included 4pcs servo motor SG90, each SG90 come with one motor/ three servo arms and three screws. Program for sg90you can build the project like “Robot Arm/ Robot hand/ control the servo with potentiometer/ multi servo control” and so on.
2. SunFounder #ad
SunFounder SG90 Micro Digital Servo Motor SF0180 for RC Helicopter Airplane Boat Robot Controls 9G 2pack #adSunFounder #ad
- Pack of two micro servos, each SG90 come with one motor/ three servo arms and three screws. Operating voltage Range is 4. 8v~6. 0v. Dead band width is 5usec. Exquisite small, make u realize bulid the robot project, it can suitable for a variety of RC Toys. Temperature range is -55 to +75.
3. HiLetgo #ad
HiLetgo 5pcs ULN2003 28BYJ-48 4-Phase Stepper Motor with 5V Drive Board for Arduino PI PIC Raspberry Pi #adHiLetgo #ad
- Voltage: 5V. Diameter: 28mm. Stepping angle: 5. 625 x 1/64. Hiletgo stepper Motor+ Driver Board. Speed down stepping motor.
4. MakerFocus #ad
MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano #adMakerFocus #ad
- User manual: please get the link from the operation guide below. I2c controlled, 12-bit resolution for each channel 4096 scales; Integrates 5V regulator, using only 2 pins; up to 16-channel servo/pwm outputs, up to 3A output current, can be powered from battery through VIN terminal.
Raspberry pi connectivity, compatible with raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano. Note: 1.
If you only connect 5v power supply to usb interface, servo cannot be driven; 2. You should connect higher power supply for higher-power servo; 3. Make sure servo are connected properly, otherwise they will not move.
Servo motor driver: you may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you. Note: the raspberry pi and servo in the photo are not included.
5. Ximimark #ad
Mini Pan/Tilt Camera Platform Anti-Vibration Camera Mount w/ 2 Servos Aircraft FPV #adXimimark #ad
- About us, professional factory, welcome to our store for more choices with best price. Including 2 SG90 servos. For any reason you are unsatisfied with our product at any time, simply contact support for exchange or refund.
Anti-vibration Camera Mount for Aircraft FPV. This is a small camera Platform. Camera is not included.
What we pursue is your satisfaction of our service, not just for our goods. They're good for beginners who want to make stuff move and the pan-tilt is an easy way to give whatever you're making both left-right and up-down motion. We will reply you about any question you ask within 24 hours.
6. Adafruit #ad
2327 - Raspberry Pi PWM Servo Hat Development Board #adAdafruit #ad
- The adafruit 16-channel 12-bit pwm/servo hat will drive up to 16 servos or pwm outputs over i2c with only 2 pins. What's more, you can stack up to 62 of them to control up to 992 servos - all with the same 2 pins! It can also do pwm up to 1.
6 khz with 12 bit precision, all completely free-running. Please note! this kit does not come with Raspberry Pi, servos, or required 5V power supply.
For use with raspberry pi model a+ or b+, can be used with the Model A or B if you use a tall 2x13 header instead of the included 2x20 The on-board pwm controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead.
7. Adafruit #ad
Adafruit Mini Pan-Tilt Kit, Assembled with Micro Servos #adAdafruit #ad
- Installing new drivers. Installation of one customer-supplied CPU. Service will take place at the customer's location. Component test and cleanup. Removal of existing CPU from desktop.
8. ELEGOO #ad
ELEGOO UNO Project Super Starter Kit with Tutorial and UNO R3 Compatible with Arduino IDE #adELEGOO #ad
- 100% compatible with arduino uno r3, MEGA 2560 R3, NANO. High quality kit with uno r3. This is the upgraded starter kits with power supply module, 9V battery with dc. The most economical kit based on Arduino platform to starting programming for those beginners who are interested.
Free pdf tutorialmore than 22 lessons and clear listing in a nice package. Lcd1602 module with pin header not need to be soldered by yourself.
9. Cocosity #ad
Cocosity Micro Servo, SG90 9G for RC Plane FPV#1, 1100KV 1100KV Brushless Motor #adCocosity #ad
- Meeting your different demands. Micro servo, quite powerful, torque is 1. 5kg/cm, weighing 9 grams, reliable in use. You can change the time to suit different brushless motors. Easy and convenient for installation, reliable and durable to use.
Full protection: low voltage cut off protection/ overheat protection/ throttle signal loss protection, compatible with lithium and nickel metal hydride batteries. 40a esc, throttle calibration function, safety protection function, support a variety of procedures and methods, comprehensive protection.
10. waveshare #ad
Servo Driver HAT for Raspberry Pi/Jetson Nano 16-Channel 2-bit I2C Interface PCA9685 Driver Supports Servo Such as SG90, MG996R, MG90S, etc #adwaveshare #ad
- Standard raspberry pi 40pin gpio extension header, supports Raspberry Pi series boards, Jetson Nano. I2c controlled, using only 2 pins; up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel 4096 scales.
Standard servo interface, mg996r, supports common used servo such as SG90, MG90S, etc. Reserved i2c control pins, allows to work with other control boards. Integrates 5v regulator, up to 3A output current, can be powered from battery through VIN terminal.
|Part Number||Servo Driver for RPI|