Top 10 BMS Protection PCB Balance Board – Battery Storage Containers

As an Amazon Associate I earn from qualifying purchases.

1. DALY

#ad

DALY BMS 10S 36V 60A Li-ion Battery Protection Module PCB Protection Board with Balance Leads Wires BMS for 18650 Battery Pack 36V

#ad
DALY #ad - Tracking information available. Battery pack low temperature(19. 4℉ / -7 ℃ charge cut-off protection and high temperature(158℉/ 70℃ discharge cut-off protection.

Quality guarantee- iso/ fcc/ rohs/ psE/ CE APPROVED. Voltage protection- bms will stop li-ion 18650 battery pack from charging when charge voltage up to 4. 25v and discharging when discharge voltage reduces to 2. 7v. Only during labor daymay 1-3, national dayoctober 1-5 and Spring FestivalFeb 9-18, 2021 need most extra 3-10 days. Shipping time-within 9-14 days from china dalyelec usually. Current protection--bms will stop li-ion 18650 battery pack from charging when charge current over 40A and discharging when discharge current over 180A.
BrandDALY #ad
ManufacturerDongguan Daly Electronics Co., Ltd. #ad
Height0.63 Inches
Length3.15 Inches
Weight0.39 Pounds
Width2.4 Inches

2. ANMBEST

#ad

Anmbest Enhanced 3S 11.1V/12V/12.6V 40A 18650 Charger PCB BMS Protection Board Li-ion Lithium Battery Charger Lipo Cell Module for Drill Motor 12.6V

#ad
ANMBEST #ad - Suitable for lithium batteries with nominal voltage of 3. 7v and full voltage of 4. 2v including 18650, polymer lithium batteries, 26650, no size limit. For 0v and 12. 6v cables, vtc4a, vtc5a, the shorter the better can not use nickel plate!!!.

Mos transistor can control the battery charge and discharge, low standby current consumption. Conditions for starting the drill: to successful starting the drill requires three 15c-20c power batteries, or six 10c-15c power batteries ordinary 18650 battery can not start the drill!! Recommended power battery models: SONY VTC4, use copper wire over 3 square millimeters, VTC6.

Highlight: over-discharge protection, overcurrent protection, overcharge protection; High charge and discharge current; Compact size and lightweight. Applications: suitable for electric drill with starting current below 80A and power below 130W. High-accuracy voltage detection circuit, fine workmanship and durable.
BrandANMBEST #ad
ManufacturerAnmbest #ad
Part NumberAnmbest_MD145

3. Organizer

#ad

Organizer 2pcs 4S 40A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board with Balance for Drill Motor 14.8V 16.8V Lipo Cell Module

#ad
Organizer #ad - 5. The battery charging detection interface with DC output in the form of needle. 1. Over charge protection, short circuit protection function, over current protection function, over discharge protection function, balance.

4. Conditions for starting the drill: to successful starting the drill requires three 15c-20c power batteries, VTC4A, or six 10C-15C power batteries ordinary 18650 battery can not start the drill!! Recommended power battery models: SONY VTC4, vtc5a, VTC6.33. Battery"-", p- charging port and port on the negative electrode. 2. Charging port of the plate and the discharge port is the same, both positive and B- connecting. Do the same mouth. For connecting cables, use copper wire over 3 square millimeters, the shorter the better can not use nickel plate!!! .
BrandOrganizer #ad
ManufacturerOrganizer #ad

4. daier

#ad

2Pcs 3S 11.1V 12.6V 25A W/Balance 18650 Li ion Lithium Battery PCB Protection Board

#ad
daier #ad - Wiring:please check the picutre 3 wiring diagramstrictly according to the diagram wiring: 0VB 3. 7vb17. 4vb211. 1vb+, need to charge first, Do not deliberately short circuit.

When the battery is connected in series with 3 groups, Please ensure that the voltage of each battery is the same. Maximum operating current: 0-25A ;Maximum transient current: 34-40A. Over voltage range: 4. 25-4. 35v ± 005v; over discharge voltage range: 2. 3-3. 0v ± 005v. After the line is connected, then have output. Attention: do not mix the good battery and poor battery to use. If not same, please fill in each set of batteries and then use. Do not mix the good battery and the battery. The internal resistance of 3 battery capacity are closer will be better.
Branddaier #ad
Manufacturerdaier #ad
Part NumberZ370*2
ModelZ370*2

5. DALY

#ad

DALY BMS 4S 12V 60A Li-ion Battery Protection Module PCB Protection Board with Balance Leads BMS for 18650 Battery Pack 12V

#ad
DALY #ad - Only during labor daymay 1-3, 2021 need most extra 3-10 days. Shipping time--you can usually receive the package within 9-14 days from dalyelec, National DayOctober 1-5 and Spring FestivalFeb 9-18, China.

Voltage protection- bms will stop li-ion 18650 battery pack from charging when charge voltage up to 4. 25v and discharging when discharge voltage reduces to 2. 7v. Battery pack low temperature(19. 4℉ / -7 ℃ charge cut-off protection and high temperature(158℉/ 70℃ discharge cut-off protection. Current protection--bms will stop li-ion 18650 battery pack from charging when charge current over 40A and discharging when discharge current over 180A. Tracking information available. Quality guarantee- iso/ fcc/ rohs/ psE/ CE APPROVED.
BrandDALY #ad
ManufacturerDongguan Daly Electronics Co., Ltd. #ad
Weight0.39 Pounds

6. Anmbest

#ad

Anmbest 5PCS 3S 11.1V/12V/12.6V 10A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell

#ad
Anmbest #ad - Mos transistor can control the battery charge and discharge, low standby current consumption. Built-in three-stage over-current detection circuit over-current 1, over-current 2, or load short circuit. Applications: massager battery pack, LED light backup power supply, 12V electronic products, solar street light battery pack, monitor standby power supply, etc. High-accuracy voltage detection circuit, fine workmanship and durable. Highlight: over-discharge protection, overcurrent protection, overcharge protection, short circuit protection; Compact size and lightweight.
BrandAnmbest #ad
ManufacturerAnmbest #ad
Part NumberAnmbest_MD35

7. FTVOGUE

#ad

FTVOGUE Battery Protection Board 3S 12V 40A Lithium Battery Charger Protection Board BMS PCB Board with Balance Charging

#ad
FTVOGUE #ad - This product has gone through load and aging test for quality assurance. With balance charging to balance the characteristic of each battery in battery pack and prolong battery life. Provide a variety of protection functions including overcharge, overdischarge, overcurrent and short circuit protection. This lithium battery protection board is adopted intelligent lithium cell management IC for fast and safe charging. Equipped with thickened aluminum fin to achieve quick heat dissipation.
BrandFTVOGUE #ad
ManufacturerFTVOGUE #ad
Height2.36 Inches
Length3.15 Inches
Weight0.02 Pounds
Width2.76 Inches
Part NumberFTVOGUEsqp1kohcxb

8. DALY

#ad

DALY BMS 13S 48V 40A Li-ion Battery Protection Module PCB Protection Board with Balance Leads BMS for 18650 Battery Pack 48V

#ad
DALY #ad - The protection board with temperature protection function will stop the battery charging and discharging to protect the battery when the battery reaches the specified temperature. Over discharge protection when the battery is discharging, the discharge must be stopped in time when it reaches a certain voltage.

Over current protection when the battery is discharged, a current is generated. If the current exceeds the maximum discharge current of the protection board, then the protection board will be powered off for a short period of time. If the battery is discharged at high current when powering on, the battery may be damaged or even exploded. If the capacity is completely discharged, it will cause permanent damage to the battery. Over charging protection when the battery is charged to the specified voltage, the protection board will stop the battery charging to avoid overcharging the battery, causing the battery to swell or even explode.

Temperature protection when the battery is charged or discharged, if the temperature is too high and the power cannot be cut off in time, the battery itself will generate heat. Short circuit protection Avoid short-circuit causing adverse effects on the battery pack. The current value is smaller than the maximum current that the battery can withstand, and it is also larger than the maximum current limit of the controller.
BrandDALY #ad
ManufacturerDongguan Daly Electronics Co., Ltd. #ad
Weight0.37 Pounds

9. Akozon

#ad

Akozon Protection Board 35A 36V BMS PCB Protection Board with Balance and Heat Dink for 18650 Li-ion Battery Cell

#ad
Akozon #ad - With balanced heat sink and 10 low internal resistance high power MOS. Scope of applicationthe bms pcb protection Board is suitable for 10-cell lithium-ion batteries, such as ternary batteries, manganic batteries and cobalt acid batteries. It has a balancing function that ensures that each battery unit is fully charged at the same time.

Unique designwiring is neat, avoiding right-angled lines and curveing the edges; reduce signal vias to avoid signal distortion and cross interference; the wiring identifications clear and easy to understand avoid misconnection. The better the battery consistency is, other batteries with solder welding, the farther the running distance is, the best performance of the protection board is; the battery should be connected in parallel and then in series. Make sure the welding is correct 18650 battery with nickel spot welding, do not use screws to avoid burning the IC of the protection board.

The continuous discharge current is 35A. Instantaneous discharge current is 100A. Necessitythe material characteristics of the lithium battery make it impossible to overcharge, overcurrent, etc. Excellent performancethe charging and discharging interfaces are the same. Notebefore installing the protection board, the batteries must be matched well. During use, overdischarge protection, over discharge, so choosing the right protection board and applying it properly is critical to the battery life.
BrandAkozon #ad
ManufacturerAkozon #ad
Height0.79 Inches
Length5.91 Inches
Width3.94 Inches
Part NumberAkozonuwt4epkiyg
Model4350281928

10. Aideepen

#ad

Aideepen 5PCS PCB Protection Boards 2S 10A 8.4V 7.4V 18650 Lithium BMS PCM PCB Li-ion Lipo 2 Cell Pack with Balance Function Charger Protection Circuit Board

#ad
Aideepen #ad - Overpressure voltage range: 2. 5-3. 0v ± 005v. Short circuit protection: can be protected, need to charge recovery. The overcharge voltage range: 4. 25-4. 35v ± 005v. The protection board couldn’t be used for lithium iron phosphate battery, hand drill battery pack, 775 4A motor, electric fish battery pack, electric bicycle battery pack, hernia lamp, 1W fish eye LED light. Included 5pcs 2s 10a pcb protection boards with balance function charger protect module.
BrandAideepen #ad
ManufacturerAideepen #ad
Part Number70127595